Mean Well PB-1000 Instruction Manual download pdf (Page 2)

PB-1000 Instruction Manual

1.MainSpecifications

PB-1000-12 PB-1000-24 PB-1000-48

MODEL

BOOSTCHARGEVOLTAGE

FLOATCHARGEVOLTAGE

BATTERY TYPE

LEAKAGECURRENTFROM

BATTERY (Typ.)

RECOMMENDEDBATTERY

CAPACITY(AMP HOURS)(Note3)

OUTPUT

VOLTAGERANGE

FREQUENCY RANGE

EFFICIENCY (Typ.)

POWERFACTOR(Typ.)

INPUT

ENVIRONMENT

INRUSHCURRENT (Typ.)

LEAKAGECURRENT

OVERTEMPERATURE

SHORTCIRCUIT

REVERSEPOLARITY

SAFETY STANDARDS

HARMONICCURRENT

EMICONDUCTION&RADIATION

SAFETY &

EMSIMMUNITY

EMC

(Note2)

WITHSTANDVOLTAGE

ISOLATIONRESISTANCE

WORKINGTEMP.

WORKINGHUMIDITY

STORAGETEMP.,HUMIDITY

TEMP.COEFFICIENT

VIBRATION

OVERVOLTAGE

PROTECTION

ACCURRENT (Typ.)

14.4V 28.8V 57.6V

13.8V

Open&SealedLead Acid

<1mA

200~600Ah

27.6V 55.2V

34.7A 17.4A

120~350Ah 60~175Ah

90~264VAC127~370VDC

47~63Hz

85%

0.95/230VAC0.98/115VACatfullload

88% 89%

12A/115VAC5.2A/230VAC

25A/115VAC50A/230VAC

<3.5mA /240VAC

16~18V 32~35V 64.5~69.5V

Protectiontype:Shutdowno/pvoltage,re-powerontorecover

80 5 (12V),85 5 (24V,48V)(TSW1:detectonheatsinkofpowertransistor)

85 5 (12V),75 5 (24V,48V)(TSW2:detectonheatsinkofo/pdiode)

Protectiontype:Shutdowno/pvoltage,recoversautomaticallyaftertemperaturegoesdown

YES,protectedbyinternalcircuit

UL60950-1, TUVEN60950-1approved

CompliancetoEN55022(CISPR22)

Complianceto EN61000-3-2,-3

CompliancetoEN61000-4-2,3,4,5,6,8,11;ENV50204,EN55024,lightindustrylevel,criteria A

I/P-O/P:3KVACI/P-FG:1.5KVACO/P-FG:0.5KVAC

I/P-O/P,I/P-FG,O/P-FG:100MOhms/500VDC 25 70%RH

-20~+60 (Refertooutputloadderatingcurve)

20~90%RHnon-condensing

-40~+85 ,10~95%RH

0.05%/ (0~50 )

10~500Hz,2G10min./1cycle,60min.eachalongX, Y,Zaxes

MTBF

127.4Khrsmin.MIL-HDBK-217F(25 )

300*184*70mm(L*W*H)

DIMENSIONOTHERS

NOTE

PACKING

3.5Kg;4pcs/15Kg/1.83CUFT

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.

2. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives.

3. This is Mean Well's suggested range. Please consult your battery manufacturer for their suggestions about maximum charging current limitation.

FUNCTION

REMOTECONTROL

BATTERBANKS

FASTCHARGE

OUTPUTOK

TEMPERATURECOMPENSATION

CHARGEROK

Open:NormalworkShort:StopCharging

2banks(A &B)

2/8stageselectable

Relaycontactrating(max.):30V/1A resistive;"Short"whenthebatteryisfull,"Open"whenthebatteryisstillcharging

Relaycontactrating(max.):30V/1A resistive;"Short"whentheunitisworkingproperly,"Open"whentheunitisfailureortheprotectionfunctionisactivating

ByNTC,compensatebothbanksatthesametime

OUTPUTCURRENT

60A

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Mean Well PB-1000 Instruction Manual Page 2

Comments to this Manuals

Related products and manuals for Battery chargers Mean Well PB-1000